EZ Dock kits Shoreline Products is an authorized EZ Dock dealer. These are four water-ready layouts you assemble and float yourself, each a platform with an approach walkway; benches where listed. Open any kit for photos, parts, and details.
Crappie Cove 9'9" x 9'9" platform + 10'2" approach
This is a do-it-yourself kit: you assemble it and set it in place yourself.
Assembly Easy · 2 people
Pricing starts at $11,573.00 plus shipping and taxes
EZ Dock DIY dock kit
Crappie Cove Pricing starts at $11,573.00 plus shipping and taxes
Assembly Easy · 2 people
Two sections of about 285 lb couple at a single seam. EZ Dock's manual has pairs of sections bolted together on shore and pushed out from there, and driving the four anchor pipes into the bed is the step many owners hand to a dealer.
Configuration 9'9" x 9'9" platform + 10'2" approach
In the kit3 60 in x 10 ft Dock Section The deck itself, in the narrower of the two molded section widths. x2 Coupler Set The rubber coupler that joins one section to the next, bolted through the molded edge pockets. The quotation lists 3 of item 301200, a pack of 2, so the kit carries 6. x6 8 in Nylon Tie-Up Cleat Bolts straight into the stainless T-nuts already molded around every section perimeter. x4 About this kit We sell and install these kits; we do not build them. The section facts below are EZ Dock’s published product information.
What the sections are made of 100% virgin LLDPE, made in the USA for 30 years. Rotationally molded, no seams or connection points. UV-ray resistant, slip-resistant surface pattern. Chamber-and-pylon flotation for stability in rough water. Standard profile carries 62.5 lbs per square foot, including dead load. Will not splinter, rot, or need painting. Cleans with soap and water. Recycled-material Dog Bone coupling, rust-resistant composite hardware. See it on your water Request this kit Bass Angler 13' x 9'9" platform + 20'4" approach + bench
This is a do-it-yourself kit: you assemble it and set it in place yourself.
Assembly Moderate · 2 to 3 people
Pricing starts at $19,472.00 plus shipping and taxes
EZ Dock DIY dock kit
Bass Angler Pricing starts at $19,472.00 plus shipping and taxes
Assembly Moderate · 2 to 3 people
Two sections of about 385 lb couple at a single seam and carry a bench. EZ Dock's manual has pairs of sections bolted together on shore and pushed out from there, and driving the four anchor pipes into the bed is the step many owners hand to a dealer.
Configuration 13' x 9'9" platform + 20'4" approach + bench
In the kit4 80 in x 10 ft Dock Section The deck itself, in the wider of the two molded section widths. x2 Coupler Set The rubber coupler that joins one section to the next, bolted through the molded edge pockets. The quotation lists 3 of item 301200, a pack of 2, so the kit carries 6. x6 8 in Nylon Tie-Up Cleat Bolts straight into the stainless T-nuts already molded around every section perimeter. x4 Polyethylene Bench with Armrests The bench with arms and cup holders, attached to the deck with the hardware it ships with. The quotation lists this part as item 300970AL; the vendor's own product page prints the number as 300970. x1 What is in the kit sheet10 About this kit We sell and install these kits; we do not build them. The section facts below are EZ Dock’s published product information.
What the sections are made of 100% virgin LLDPE, made in the USA for 30 years. Rotationally molded, no seams or connection points. UV-ray resistant, slip-resistant surface pattern. Chamber-and-pylon flotation for stability in rough water. Standard profile carries 62.5 lbs per square foot, including dead load. Will not splinter, rot, or need painting. Cleans with soap and water. Recycled-material Dog Bone coupling, rust-resistant composite hardware. See it on your water Request this kit Redear Retreat 19'6" x 9'9" platform + 20'4" approach + bench
This is a do-it-yourself kit: you assemble it and set it in place yourself.
Assembly Moderate · 3 people
Pricing starts at $23,158.00 plus shipping and taxes
EZ Dock DIY dock kit
Redear Retreat Pricing starts at $23,158.00 plus shipping and taxes
Assembly Moderate · 3 people
Three sections of about 385 lb meet at two seams, and EZ Dock's manual advises against moving more than two coupled floats at once, so the last section is coupled on the water. Driving the four anchor pipes into the bed is the step many owners hand to a dealer.
Configuration 19'6" x 9'9" platform + 20'4" approach + bench
In the kit4 80 in x 10 ft Dock Section The deck itself, in the wider of the two molded section widths. x3 Coupler Set The rubber coupler that joins one section to the next, bolted through the molded edge pockets. The quotation lists 6 of item 301200, a pack of 2, so the kit carries 12. x12 8 in Nylon Tie-Up Cleat Bolts straight into the stainless T-nuts already molded around every section perimeter. x4 Polyethylene Bench with Armrests The bench with arms and cup holders, attached to the deck with the hardware it ships with. The quotation lists this part as item 300970AL; the vendor's own product page prints the number as 300970. x1 About this kit We sell and install these kits; we do not build them. The section facts below are EZ Dock’s published product information.
What the sections are made of 100% virgin LLDPE, made in the USA for 30 years. Rotationally molded, no seams or connection points. UV-ray resistant, slip-resistant surface pattern. Chamber-and-pylon flotation for stability in rough water. Standard profile carries 62.5 lbs per square foot, including dead load. Will not splinter, rot, or need painting. Cleans with soap and water. Recycled-material Dog Bone coupling, rust-resistant composite hardware. See it on your water Request this kit Catfish Camp 19'6" x 13' platform + 20'4" approach + two benches
This is a do-it-yourself kit: you assemble it and set it in place yourself.
Assembly Involved · 3 to 4 people
Pricing starts at $28,846.00 plus shipping and taxes
EZ Dock DIY dock kit
Catfish Camp Pricing starts at $28,846.00 plus shipping and taxes
Assembly Involved · 3 to 4 people
Four sections of about 385 lb meet at four seams and twenty coupler sets, the most in-water coupling of the four kits, and EZ Dock's manual calls for its own in-water coupler tool. Driving the four anchor pipes into the bed is the step many owners hand to a dealer.
Configuration 19'6" x 13' platform + 20'4" approach + two benches
In the kit4 80 in x 10 ft Dock Section The deck itself, in the wider of the two molded section widths. x4 Coupler Set The rubber coupler that joins one section to the next, bolted through the molded edge pockets. The quotation lists 10 of item 301200, a pack of 2, so the kit carries 20. x20 8 in Nylon Tie-Up Cleat Bolts straight into the stainless T-nuts already molded around every section perimeter. x8 Polyethylene Bench with Armrests The bench with arms and cup holders, attached to the deck with the hardware it ships with. The quotation lists this part as item 300970AL; the vendor's own product page prints the number as 300970. x2 About this kit We sell and install these kits; we do not build them. The section facts below are EZ Dock’s published product information.
What the sections are made of 100% virgin LLDPE, made in the USA for 30 years. Rotationally molded, no seams or connection points. UV-ray resistant, slip-resistant surface pattern. Chamber-and-pylon flotation for stability in rough water. Standard profile carries 62.5 lbs per square foot, including dead load. Will not splinter, rot, or need painting. Cleans with soap and water. Recycled-material Dog Bone coupling, rust-resistant composite hardware. See it on your water Request this kit Pricing does not include taxes, delivery, or installation. Prices are EZ Dock of Texas quotations dated August 6, 2026, materials only. The Bass Angler is priced from the EZ Dock kit sheet on file August 25, 2026, which draws two sections; no quotation on file states that figure.
Renders show the platform sections. Each kit includes the approach walkway and any benches listed.
